- CPU SPEED ACCELERATOR 6.2 SERIAL HOW TO
- CPU SPEED ACCELERATOR 6.2 SERIAL SOFTWARE
- CPU SPEED ACCELERATOR 6.2 SERIAL CODE
> DSP1SS Initialization is DONE! > START => Enable 元 ClkĬortexA15_0: GEL Output: > Change Suspend source for GPTimer5 to DSP1ĬortexA15_0: GEL Output: -> DSP2SS Initialization is in progress. > IPU2SS Initialization is DONE! > DSP1SS Initialization is in progress. > IPU1SS Initialization is DONE! > IPU2SS Initialization is in progress. > DDR3 Initialization is DONE! > AM572x Target Connect Sequence DONE !!!!! > IPU1SS Initialization is in progress. > PRCM Configuration for all modules is DONE! > DDR3 Initialization is in progress. > PRCM Clock Configuration for OPP 0 is DONE! > PRCM Configuration for all modules in progress. > I2C Init > AM572x Begin MMC2 Pad Configuration > AM572x End MMC2 Pad Configuration > AM572x PG2.0 GP device > PRCM Clock Configuration for OPPNOM in progress. IcePick_D: GEL Output: IVAHD ICONT2 is released from Wait-In-Reset.ĬS_DAP_DebugSS: GEL Output: -> CONFIGURE DEBUG DPLL settings to 1.9 GHZs Setup DebugSS 1.9GHz in progress.ĬS_DAP_DebugSS: GEL Output: > TURNING ON 元_INSTR and 元_3 clocks required for debug instrumention > -ĬS_DAP_DebugSS: GEL Output: -> Mapping TIMER supsend sources to default cores > AM572x GP EVM > AM572x Target Connect Sequence Begins.
IcePick_D: GEL Output: IVAHD ICONT1 is released from Wait-In-Reset.
CPU SPEED ACCELERATOR 6.2 SERIAL SOFTWARE
Package with support for Sitara Processors and done the software updateĬorrectly from the Help Menu to get the latest Sitara CSP package.
GPEVM_AM572x_SiRevA target make sure you have installed the CCSv6 Note: For older revisions of CCSv6, If you don`t find the Select Spectrum digital XDS200 emulator and Launch CCS and create new target configuration(File->New->TargetĬonfiguration file) as shown in the images below and provide appropriate Connect to EVM after booting an image from the SD card.Connect to EVM without a SD card boot image to boot the EVM.There are two scenarios while connecting to the EVM : In that case, the connection hasįailed, hit connect in CCS debug view without removing the powerĬable and then immediately hit the power switch besides the power It means that the PMIC switched off before the GEL could initialize If the above CCS connect sequence does not work in the first attempt,.Target configuration to 15Mhz or to the maximum (20Mhz). To allow quicker execution of the GEL before the PMIC shuts off, youĬan increase the JTAG TCLK Frequency in Advance settings of your.Scenario, the SBL component provides the same functionality
CPU SPEED ACCELERATOR 6.2 SERIAL CODE
In Linux boot, the uboot code keeps the PMIC On and in the TI RTOS boot While booting from ROM bootloader userĪpplication software, would need to keep the PMIC ON while initializing In emulation setup, the GEL file will keep the PMIC on after you connect After seven seconds, the PMIC powers off unless software writes Off the board in seven seconds after power on to work around a hardwareĮrrata. The Power Management Integrated Circuit (PMIC) on the TMDSEVM572X turns Female barrel with 2.5mm inner diameter and 5.5mm outer diameter.Positive inner and negative outer terminals.Please note that a power supply is NOT included with the AM572xĮvaluation Module and needs to be purchased separately.
CPU SPEED ACCELERATOR 6.2 SERIAL HOW TO
Image for how to connect the XDS200 Emulator to the 20 pin header is XDS560v2-class JTAG debug probes (high performance).XDS200-class JTAG debug probes (recommended).XDS100-class JTAG debug probes (low cost, low performance).List of standalone JTAG debug probes supported: JTAG debug probes (aka Emulators) supported HDMI cable for optional external display.The AM572x Evaluation Module also integrates video and 3D/2D graphicsĪcceleration, as well as a qual-core Programmable Real-time Unit (PRU) It is a development platform based on the dual ARMĬortex-A15, dual C66x DSP processor that is integrated with tons ofĬonnectivity such as PCIe, SATA, HDMI, USB 3.0/2.0, Dual Gigabit Vision, networking, medical imaging and many other industrialĪpplications. Start evaluation of Sitara™ ARM® Cortex®-A15 AM57x Processors (AM5728,ĪM5726, AM5718, AM5716) and accelerate development for HMI, machine The AM572x Evaluation Module provides an affordable platform to quickly
0 kommentar(er)
